Dzisiaj jest 16 sty 2022, 20:19

Strefa czasowa UTC+1godz. [letni]




Nowy temat Odpowiedz w temacie  [ Posty: 82 ]  Przejdź na stronę Poprzednia  1, 2, 3, 4, 5  Następna
Autor Wiadomość
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:01 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
Dzisiaj jeszcze raz wgrałem mu ten Twój testowy soft ale tym razem przez jboota i logi są nieco innego. Wykrywa modem :)

Lan jak poprzednio 1 i 4 1Gbit , 2 i 3 10Mbit oczywiście nie przydziela IP

CDG57BDL_0T3 Jboot B1197
AR8327/AR8334/8337 id ==> 0x1302
AR8327/AR8337 id ==> 0x1302
JRecovery Version R1.2 2017/03/20 14:12
Test Memory [128MB] Successful
spi device id: ef 70 18 0 0 (70180000)
Warning: un-recognized spi deice id: ef 70 18 0 0 (70180000)
.
...........................
Starting kernel @80000000...
[ 0.000000] Linux version 5.4.158 (cezary@eko.one.pl) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15819-0011c7ad12)) #0 Sun Nov 14 19:24:45 2021
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-961
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=0000e5f2
[ 0.000000] Readback ErrCtl register=0000e5f2
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 122404K/131072K available (5064K kernel code, 204K rwdata, 632K rodata, 1196K init, 213K bss, 8668K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x805c5a28 with crng_init=0
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000009] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015506] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.059579] pid_max: default: 32768 minimum: 301
[ 0.068944] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.083352] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105168] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.124473] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.138074] pinctrl core: initialized pinctrl subsystem
[ 0.149912] NET: Registered protocol family 16
[ 0.639146] PCI host bridge /pcie@10140000 ranges:
[ 0.648547] MEM 0x0000000020000000..0x000000002fffffff
[ 0.658913] IO 0x0000000010160000..0x000000001016ffff
[ 0.692269] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.703317] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.715896] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.726911] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.739497] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.750512] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.763106] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.773945] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.786947] PCI host bridge to bus 0000:00
[ 0.795002] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.808614] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
[ 0.822287] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.835785] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.851578] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
[ 0.863514] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 0.875947] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 0.888474] pci 0000:00:00.0: supports D1
[ 0.896363] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.909765] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.925780] pci 0000:01:00.0: [14c3:7612] type 00 class 0x028000
[ 0.937661] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 0.951124] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.964509] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.978526] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.991575] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 1.004725] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.017847] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.031692] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 1.045193] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 1.059557] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 1.073068] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 1.087612] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 1.101959] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.111826] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 1.125325] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 1.139803] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 1.165582] clocksource: Switched to clocksource systick
[ 1.177157] thermal_sys: Registered thermal governor 'step_wise'
[ 1.177672] NET: Registered protocol family 2
[ 1.198316] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 1.213430] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 1.230003] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.245167] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.259177] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.271966] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.284876] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.298999] NET: Registered protocol family 1
[ 1.307624] PCI: CLS 0 bytes, default 32
[ 1.318542] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 1.332681] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 1.353672] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.365139] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.400237] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.417929] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.433347] printk: console [ttyS0] disabled
[ 1.441820] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 1.461458] printk: console [ttyS0] enabled
[ 1.461458] printk: console [ttyS0] enabled
[ 1.478041] printk: bootconsole [early0] disabled
[ 1.478041] printk: bootconsole [early0] disabled
[ 1.506008] spi spi0.0: force spi mode3
[ 1.523512] spi-nor spi0.0: w25q128jv (16384 Kbytes)
[ 1.533483] 3 fixed-partitions partitions found on MTD device spi0.0
[ 1.546148] Creating 3 MTD partitions on "spi0.0":
[ 1.555701] 0x000000000000-0x000000010000 : "jboot"
[ 1.566547] 0x000000010000-0x000000ff0000 : "firmware"
[ 1.580030] 2 jimage-fw partitions found on MTD device firmware
[ 1.591907] Creating 2 MTD partitions on "firmware":
[ 1.601816] 0x000000000000-0x0000001e622b : "kernel"
[ 1.612811] 0x0000001e622b-0x000000fe0000 : "rootfs"
[ 1.623782] mtd: device 3 (rootfs) set to be root filesystem
[ 1.637165] 1 squashfs-split partitions found on MTD device rootfs
[ 1.649591] 0x0000006a7000-0x000000fe0000 : "rootfs_data"
[ 1.661477] 0x000000ff0000-0x000001000000 : "config"
[ 1.673355] libphy: Fixed MDIO Bus: probed
[ 1.691858] gsw: setting port4 to ephy mode
[ 1.700363] mtk_soc_eth 10100000.ethernet: generated random MAC address 26:6e:d7:74:2f:2c
[ 1.716888] libphy: mdio: probed
[ 1.725841] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus
[ 1.815279] random: fast init done
[ 1.945541] mtk_soc_eth 10100000.ethernet: using fixed link parameters
[ 1.958895] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.971414] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.988458] rt2880_wdt 10000120.watchdog: Initialized
[ 2.000195] NET: Registered protocol family 10
[ 2.013699] Segment Routing with IPv6
[ 2.021209] NET: Registered protocol family 17
[ 2.030158] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.055999] 8021q: 802.1Q VLAN Support v1.8
[ 2.070962] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.091892] Freeing unused kernel memory: 1196K
[ 2.100942] This architecture does not have kernel memory protection.
[ 2.113772] Run /sbin/init as init process
[ 2.959296] init: Console is alive
[ 2.966426] init: - watchdog -
[ 4.609377] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.682606] usbcore: registered new interface driver usbfs
[ 4.693700] usbcore: registered new interface driver hub
[ 4.704434] usbcore: registered new device driver usb
[ 4.721437] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.736387] ehci-fsl: Freescale EHCI Host controller driver
[ 4.749138] ehci-platform: EHCI generic platform driver
[ 4.769969] phy phy-usbphy.0: remote usb device wakeup disabled
[ 4.781780] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 4.790638] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.802145] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 4.818081] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.834922] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.848451] hub 1-0:1.0: USB hub found
[ 4.856452] hub 1-0:1.0: 1 port detected
[ 4.869649] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.883845] ohci-platform: OHCI generic platform driver
[ 4.894630] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 4.908230] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 4.924154] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.961313] hub 2-0:1.0: USB hub found
[ 4.969300] hub 2-0:1.0: 1 port detected
[ 4.984145] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.003078] init: - preinit -
[ 6.371325] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.469847] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.759862] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.822247] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[ 7.838474] 8021q: adding VLAN 0 to HW filter on device eth0
[ 7.850269] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 7.900378] urandom_read: 4 callbacks suppressed
[ 7.900388] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.224767] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.515564] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 9.535502] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 9.645847] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[ 9.679820] procd: - early -
[ 9.685866] procd: - watchdog -
[ 10.226326] procd: - watchdog -
[ 10.258104] procd: - ubus -
[ 10.414401] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.434994] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.452604] procd: - init -
Please press Enter to activate this console.
[ 11.579532] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.658972] tun: Universal TUN/TAP device driver, 1.6
[ 11.808214] usbcore: registered new interface driver cdc_wdm
[ 12.052890] urngd: jent-rng init failed, err: 2
[ 12.104137] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
[ 12.119308] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
[ 12.217968] usbcore: registered new interface driver usbserial_generic
[ 12.231152] usbserial: USB Serial support registered for generic
[ 12.259093] xt_time: kernel timezone is -0000
[ 12.468493] PPP generic driver version 2.4.2
[ 12.480164] NET: Registered protocol family 24
[ 12.492988] usbcore: registered new interface driver qmi_wwan
[ 12.526513] wireguard: WireGuard 1.0.0 loaded. See http://www.wireguard.com for information.
[ 12.542191] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 12.588394] usbcore: registered new interface driver option
[ 12.599689] usbserial: USB Serial support registered for GSM modem (1-port)
[ 12.638489] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 12.658496] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[ 12.676732] rt2800_wmac 10180000.wmac: Falling back to sysfs fallback for: soc_wmac.eeprom
[ 12.994420] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 13.009973] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 13.061448] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 24.641116] random: crng init done
[ 54.155993] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[ 54.172045] 8021q: adding VLAN 0 to HW filter on device eth0
[ 54.219415] device eth0 entered promiscuous mode
[ 54.254508] Atheros AR8216/AR8236/AR8316 mdio-bus:00: Port 5 is up
[ 54.267088] br-lan: port 1(eth0.1) entered blocking state
[ 54.277863] br-lan: port 1(eth0.1) entered disabled state
[ 54.289006] device eth0.1 entered promiscuous mode
[ 54.355761] br-lan: port 1(eth0.1) entered blocking state
[ 54.366604] br-lan: port 1(eth0.1) entered forwarding state
[ 55.174739] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 64.893590] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 64.937653] jffs2_build_filesystem(): unlocking the mtd device...
[ 64.941605] done.
[ 64.957778] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 75.917520] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 76.154012] option 1-1:1.0: GSM modem (1-port) converter detected
[ 76.166575] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 76.245983] option 1-1:1.2: GSM modem (1-port) converter detected
[ 76.258506] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 76.273258] option 1-1:1.3: GSM modem (1-port) converter detected
[ 76.285807] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 76.448311] qmi_wwan 1-1:1.4: cdc-wdm0: USB WDM device
[ 76.484743] qmi_wwan 1-1:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1, WWAN/QMI device, 0a:c1:19:49:30:b7
[ 128.672916] done.
[ 128.676816] jffs2: notice: (3015) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 129.115911] overlayfs: upper fs does not support tmpfile.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:04 
Online
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 14012
Lokalizacja: Warszawa
Bo obraz zmieniłem wieczorem. Wifi masz (zobacz czy oba), modem jest, sprawdź ledy i przyciski.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:05 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
Komenda:

echo 0 > /sys/class/gpio/gpio0/value wyłącza modem

echo 1 > /sys/class/gpio/gpio0/value włącza modem

czyli jak w dwr960


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:05 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
A ok nie wiedziałem że zmieniłeś. Akurat pobrałem ze strony.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:08 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
jaką komenda sprawdzić wifi?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:10 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
Ok chyba działa:) a przynajmniej te na 2,4

root@OpenWrt:/# iwinfo wlan0 scan
[ 352.205482] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
[ 352.222155] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
[ 354.056144] ieee80211 phy0: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
[ 354.075731] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[ 354.103642] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 0, phase= 0)
[ 354.122753] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[ 354.150645] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= f, phase=3d)
[ 354.168879] ieee80211 phy0: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
[ 354.193683] ieee80211 phy0: rt2800_rxiq_calibration: Warning - RXIQ calibration FAIL
[ 354.219373] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=0, Ph_rx=-5
Cell 01 - Address: 8
ESSID: "Uhygfh818"
Mode: Master Channel: 1
Signal: -68 dBm Quality: 42/70
Encryption: WPA2 PSK (TKIP, CCMP)
HT Operation:
Primary Channel: 1
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 02 - Address: :A8
ESSID: "UPgh64251"
Mode: Master Channel: 1
Signal: -74 dBm Quality: 36/70
Encryption: WPA2 PSK (TKIP, CCMP)
HT Operation:
Primary Channel: 1
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 03 - Address:
ESSID: "RLC"
Mode: Master Channel: 3
Signal: -74 dBm Quality: 36/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 3
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 04 - Address: 1
ESSID: "zima"
Mode: Master Channel: 5
Signal: -52 dBm Quality: 58/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 5
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 05 - Address:
ESSID: "UP3"
Mode: Master Channel: 6
Signal: -90 dBm Quality: 20/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 6
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 06 - Address: 30
ESSID: "Wi-Free #InternetUPCNajszybszy"
Mode: Master Channel: 6
Signal: -90 dBm Quality: 20/70
Encryption: WPA2 802.1X (TKIP, CCMP)
HT Operation:
Primary Channel: 6
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 07 - Address: 74
ESSID: "soroczka"
Mode: Master Channel: 8
Signal: -38 dBm Quality: 70/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 8
Secondary Channel Offset: below
Channel Width: unknown

Cell 08 - Address: 3
ESSID: "UP"
Mode: Master Channel: 11
Signal: -62 dBm Quality: 48/70
Encryption: mixed WPA/WPA2 PSK (TKIP, CCMP)
HT Operation:
Primary Channel: 11
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 09 - Address: 3
ESSID: "Wi-Free #InternetUPCNajszybszy"
Mode: Master Channel: 11
Signal: -62 dBm Quality: 48/70
Encryption: WPA2 802.1X (TKIP, CCMP)
HT Operation:
Primary Channel: 11
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 10 - Address: 91
ESSID: "U"
Mode: Master Channel: 11
Signal: -82 dBm Quality: 28/70
Encryption: mixed WPA/WPA2 PSK (TKIP, CCMP)
HT Operation:
Primary Channel: 11
Secondary Channel Offset: no secondary
Channel Width: unknown

Cell 11 - Address:
ESSID: "Wi-Free #InternetUPCNajszybszy"
Mode: Master Channel: 11
Signal: -82 dBm Quality: 28/70
Encryption: WPA2 802.1X (TKIP, CCMP)
HT Operation:
Primary Channel: 11
Secondary Channel Offset: no secondary
Channel Width: unknown

root@OpenWrt:/#

iwinfo wlan1 scan nie działa

iwinfo wlan2 scan nie działa

chyba nie widzi karty od 5GHz


W dwr960 wlan0 to było 5GHz a wlan1 to 2,4 zmieniałeś coś tutaj czy to zależy co najpierw wykryje>


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:20 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
Dioda lan jak wpinam w port 1 lub 4 zapala się. Jak w 2 lub 3 to nie. Jak skanowałem eter zapaliła mi się dioda od 2,4 wifi. Po odpaleniu routera są włączone dioda wan i ststus


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:23 
Online
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 14012
Lokalizacja: Warszawa
Nie wiem czym ta karta jest. To jest qualcomm, miediatek czy coś innego?

Ale sprawdź mi tak po prostu czy wpisane 1 zapali daną led, a zero zgasi czy nie, które działa a które nie, jak nie działa to poszukaj gpio na którym jest dioda.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:25 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
A gdzie jest rozpiska diod od dwr960?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:27 
Online
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 14012
Lokalizacja: Warszawa
W /sys/class/leds masz. Sprawdź tez czy przyciski działają.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:43 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
Próbowałem otworzyć tą 5GHz ale zalana jest jakimś syfem. W ogóle ciężko ją było od płyty oderwać tak nawalone kleju. Z góry zakładają, że nikt tego nie będzie ruszał ech...

Zaktualizowałem pierwszy post o zdjęcie tej karty. Zobacz Cezary może coś z niej wyczytasz...


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:44 
Online
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 14012
Lokalizacja: Warszawa
Zainstaluj sobie pciutils i pokaz lspci.

EDIT: pachnie to jakimś qualcommem, więc może po prostu muszę włożyć ath10k do obrazu. Tak czy siak - wieczorem dopiero, mogę to zrobić, więc sprawdzaj gpio i zobacz ten lspci.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 11:54 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
Ok ale jak mam go wrzucić na pacjenta jak mi nawet winscp nie działa? A w ogóle to swich jest teraz przezroczysty wpiąłem mu neta do wan a sam jest podpięty do 4 i mam adres z podsieci wcześniejszego routera


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 12:05 
Online
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 14012
Lokalizacja: Warszawa
Wifi masz przecież. Uruchom sobie np. jako klienta i możesz ściągać.

PS. modem też masz i mozesz sobie ustawić połącznie przez modem.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 12:13 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
root@OpenWrt:/# lspci
00:00.0 PCI bridge: Ralink corp. Device 0801 (rev 01)
01:00.0 Network controller: MEDIATEK Corp. MT7612E 802.11acbgn PCI Express Wireless Network Adapter
root@OpenWrt:/#


coś mi nie idzie z gpio

root@OpenWrt:/# echo "2" > /sys/class/gpio/export
ash: write error: Resource busy
root@OpenWrt:/#


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 12:18 
Online
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 14012
Lokalizacja: Warszawa
Taa, nie ten sterownik. Poczekaj.

Nie wszystkie gpio możesz wyeksportować, te używane lub już wyeksportowane nie, bo one już są. tylko wpisz do nich 1 lub 0

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 12:32 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
green:3g - prawidłowo green:status - prawidłowo
green:4g - prawidłowo green:wan - prawidłowo
green:lan - prawidłowo green:wlan2g - prawidłowo
green:signal - prawidłowo green:wlan5g - prawidłowo
green:sms - prawidłowo red:signal - prawidłowo


Skubany dopiero teraz zauważyłem że w miejscu gdzie wdr960 miał puste ten ma wlutowane 2 kolejne diody czyli w sumie 2 wiersze po 5 diod - ciekawe czy pod gpio podłączone


Ostatnio zmieniony 18 lis 2021, 12:36 przez smereka, łącznie zmieniany 1 raz

Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 12:33 
Online
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 14012
Lokalizacja: Warszawa
Pobierz i wgraj obraz jeszcze raz.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 12:48 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
Działają teraz 2 radyjka a przynajmniej w tym sensie że mi skanują eter i wyświetlają sieci Diody od wifi też zapalają się prawidłowo. Porty bez zmian

Starting kernel @80000000...
[ 0.000000] Linux version 5.4.158 (cezary@eko.one.pl) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15819-0011c7ad12)) #0 Wed Nov 17 19:44:26 2021
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-961
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=0000edf0
[ 0.000000] Readback ErrCtl register=0000edf0
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 122404K/131072K available (5064K kernel code, 204K rwdata, 632K rodata, 1196K init, 213K bss, 8668K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x805c5a28 with crng_init=0
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000009] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015508] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.059570] pid_max: default: 32768 minimum: 301
[ 0.068935] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.083341] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105160] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.124466] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.138067] pinctrl core: initialized pinctrl subsystem
[ 0.149905] NET: Registered protocol family 16
[ 0.417076] PCI host bridge /pcie@10140000 ranges:
[ 0.426476] MEM 0x0000000020000000..0x000000002fffffff
[ 0.436842] IO 0x0000000010160000..0x000000001016ffff
[ 0.470202] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.481251] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.493830] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.504844] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.517430] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.528446] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.541040] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.551879] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.564882] PCI host bridge to bus 0000:00
[ 0.572937] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.586551] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
[ 0.600223] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.613722] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.629514] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
[ 0.641451] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 0.653883] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 0.666412] pci 0000:00:00.0: supports D1
[ 0.674299] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.687715] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.703731] pci 0000:01:00.0: [14c3:7612] type 00 class 0x028000
[ 0.715612] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 0.729075] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.742460] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.756438] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.769486] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.782637] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.795758] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.809603] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.823104] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.837468] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.850979] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.865521] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.879871] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.889738] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.903237] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.917715] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.943492] clocksource: Switched to clocksource systick
[ 0.955068] thermal_sys: Registered thermal governor 'step_wise'
[ 0.955584] NET: Registered protocol family 2
[ 0.976229] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.991341] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 1.007914] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.023077] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.037088] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.049876] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.062785] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.076908] NET: Registered protocol family 1
[ 1.085532] PCI: CLS 0 bytes, default 32
[ 1.096452] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 1.110591] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 1.131575] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.143042] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.178134] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.195827] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.211243] printk: console [ttyS0] disabled
[ 1.219717] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 1.239356] printk: console [ttyS0] enabled
[ 1.239356] printk: console [ttyS0] enabled
[ 1.255936] printk: bootconsole [early0] disabled
[ 1.255936] printk: bootconsole [early0] disabled
[ 1.283905] spi spi0.0: force spi mode3
[ 1.301422] spi-nor spi0.0: w25q128jv (16384 Kbytes)
[ 1.311394] 3 fixed-partitions partitions found on MTD device spi0.0
[ 1.324058] Creating 3 MTD partitions on "spi0.0":
[ 1.333612] 0x000000000000-0x000000010000 : "jboot"
[ 1.344461] 0x000000010000-0x000000ff0000 : "firmware"
[ 1.357941] 2 jimage-fw partitions found on MTD device firmware
[ 1.369817] Creating 2 MTD partitions on "firmware":
[ 1.379726] 0x000000000000-0x0000001e620b : "kernel"
[ 1.390718] 0x0000001e620b-0x000000fe0000 : "rootfs"
[ 1.401689] mtd: device 3 (rootfs) set to be root filesystem
[ 1.415064] 1 squashfs-split partitions found on MTD device rootfs
[ 1.427490] 0x0000006ab000-0x000000fe0000 : "rootfs_data"
[ 1.439380] 0x000000ff0000-0x000001000000 : "config"
[ 1.451262] libphy: Fixed MDIO Bus: probed
[ 1.469750] gsw: setting port4 to ephy mode
[ 1.478255] mtk_soc_eth 10100000.ethernet: generated random MAC address 32:07:6b:a6:d6:d7
[ 1.494777] libphy: mdio: probed
[ 1.503746] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus
[ 1.602801] random: fast init done
[ 1.725029] mtk_soc_eth 10100000.ethernet: using fixed link parameters
[ 1.738381] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.750899] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.767945] rt2880_wdt 10000120.watchdog: Initialized
[ 1.779679] NET: Registered protocol family 10
[ 1.793192] Segment Routing with IPv6
[ 1.800701] NET: Registered protocol family 17
[ 1.809650] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.835491] 8021q: 802.1Q VLAN Support v1.8
[ 1.850452] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.871387] Freeing unused kernel memory: 1196K
[ 1.880437] This architecture does not have kernel memory protection.
[ 1.893268] Run /sbin/init as init process
[ 2.814160] init: Console is alive
[ 2.821356] init: - watchdog -
[ 4.440938] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.514584] usbcore: registered new interface driver usbfs
[ 4.525645] usbcore: registered new interface driver hub
[ 4.536377] usbcore: registered new device driver usb
[ 4.553421] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.568354] ehci-fsl: Freescale EHCI Host controller driver
[ 4.581124] ehci-platform: EHCI generic platform driver
[ 4.601953] phy phy-usbphy.0: remote usb device wakeup disabled
[ 4.613765] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 4.622623] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.634116] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 4.650042] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.668028] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.681552] hub 1-0:1.0: USB hub found
[ 4.689554] hub 1-0:1.0: 1 port detected
[ 4.702879] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.716991] ohci-platform: OHCI generic platform driver
[ 4.727779] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 4.741379] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 4.757299] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.794442] hub 2-0:1.0: USB hub found
[ 4.802432] hub 2-0:1.0: 1 port detected
[ 4.817286] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.836223] init: - preinit -
[ 6.269149] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.367123] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.657487] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.662435] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[ 7.678761] 8021q: adding VLAN 0 to HW filter on device eth0
[ 7.690497] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 7.740649] urandom_read: 4 callbacks suppressed
[ 7.740658] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.073278] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.796616] jffs2: notice: (518) jffs2_build_xattr_subsystem: complete building xattr subsystem, 8 of xdatum (7 unchecked, 1 orphan) and 10 of xref (1 dead, 0 orphan) found.
[ 9.829952] mount_root: switching to jffs2 overlay
[ 9.846636] overlayfs: upper fs does not support tmpfile.
[ 9.864051] urandom-seed: Seeding with /etc/urandom.seed
[ 9.994814] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[ 10.029206] procd: - early -
[ 10.035253] procd: - watchdog -
[ 10.539151] procd: - watchdog -
[ 10.570881] procd: - ubus -
[ 10.736725] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.756645] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.774214] procd: - init -
Please press Enter to activate this console.
[ 11.939292] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.020707] tun: Universal TUN/TAP device driver, 1.6
[ 12.173794] usbcore: registered new interface driver cdc_wdm
[ 12.410906] urngd: jent-rng init failed, err: 2
[ 12.466378] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
[ 12.481558] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
[ 12.580730] usbcore: registered new interface driver usbserial_generic
[ 12.593908] usbserial: USB Serial support registered for generic
[ 12.621578] xt_time: kernel timezone is -0000
[ 12.793556] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
[ 12.806202] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[ 12.818321] mt76x2e 0000:01:00.0: EEPROM data check failed: 7620
[ 13.049396] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[ 13.066706] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[ 13.077715] mt76x2e 0000:01:00.0: Build: 1
[ 13.085879] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[ 13.107060] mt76x2e 0000:01:00.0: Firmware running!
[ 13.282161] PPP generic driver version 2.4.2
[ 13.293823] NET: Registered protocol family 24
[ 13.306619] usbcore: registered new interface driver qmi_wwan
[ 13.341020] wireguard: WireGuard 1.0.0 loaded. See http://www.wireguard.com for information.
[ 13.356711] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 13.457815] usbcore: registered new interface driver option
[ 13.469115] usbserial: USB Serial support registered for GSM modem (1-port)
[ 13.534392] ieee80211 phy1: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 13.621365] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 13.636918] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 13.659521] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 20.814697] random: crng init done
[ 27.444718] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[ 27.460802] 8021q: adding VLAN 0 to HW filter on device eth0
[ 27.517132] device eth0 entered promiscuous mode
[ 27.548313] Atheros AR8216/AR8236/AR8316 mdio-bus:00: Port 1 is up
[ 27.560825] Atheros AR8216/AR8236/AR8316 mdio-bus:00: Port 2 is up
[ 27.573596] br-lan: port 1(eth0.1) entered blocking state
[ 27.584356] br-lan: port 1(eth0.1) entered disabled state
[ 27.595489] device eth0.1 entered promiscuous mode
[ 27.690961] br-lan: port 1(eth0.1) entered blocking state
[ 27.701804] br-lan: port 1(eth0.1) entered forwarding state
[ 28.454011] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 43.527011] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 43.609885] option 1-1:1.0: GSM modem (1-port) converter detected
[ 43.622482] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 43.668580] option 1-1:1.2: GSM modem (1-port) converter detected
[ 43.681125] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 43.695880] option 1-1:1.3: GSM modem (1-port) converter detected
[ 43.708393] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 43.787201] qmi_wwan 1-1:1.4: cdc-wdm0: USB WDM device
[ 43.807971] qmi_wwan 1-1:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1, WWAN/QMI device, 8e:01:7b:aa:98:1d


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-961 Telnor młodszy braciszek 960? - zobaczymy
Post: 18 lis 2021, 12:50 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 433
BusyBox v1.33.1 (2021-07-06 00:04:09 UTC) built-in shell (ash)

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------------------------------
| |
| OpenWrt 21.02-SNAPSHOT, r16337-df363764b7 |
| |
| Build time: 2021-11-18 11:28 CET |
| Cezary Jackiewicz, https://eko.one.pl |
| |
-----------------------------------------------------------------------------
| Machine: D-Link DWR-961 |
| Uptime: 0d, 00:00:57 |
| Load: 0.76 0.24 0.08 |
| Flash: total: 9.2MB, free: 8.7MB, used: 5% |
| Memory: total: 120.7MB, free: 102.8MB, used: 14% |
| Leases: 0 |
| lan: static, 192.168.1.1 |
| wan: dhcp, ? |
| wan6: dhcpv6, ? |
-----------------------------------------------------------------------------
=== WARNING! ================================================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
-----------------------------------------------------------------------------



zobacz Ty wykryło odpowiednio ram. Gdzie w jego braciszku w oenwrt pokazuje 64


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
Wyświetl posty nie starsze niż:  Sortuj wg  
Nowy temat Odpowiedz w temacie  [ Posty: 82 ]  Przejdź na stronę Poprzednia  1, 2, 3, 4, 5  Następna

Strefa czasowa UTC+1godz. [letni]


Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 29 gości


Nie możesz tworzyć nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów

Szukaj:
Przejdź do:  
designed by digi-led.pl
...Copyright © 2010-2013, Ekipa openrouter.info